mypros+
Error code reference

Electrolux Oven Error Code Fd13

Lower Inverter Communication Error

Electrolux codesElectrolux oven codes

Lower Inverter Communication Error - stops machine. Inverter power supply (AC) missing, connector unplugged/damaged, or fuse F2 blown. Detection mode: signal missing for more than 25 seconds.

First step from the service manual

Check inverter power supply (AC); check Connector J1 and J2 (PMACS); check fuse F2.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for Fd13.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What Fd13 means on a Electrolux oven

The Fd13 error code on an Electrolux oven indicates a Lower Inverter Communication Error, meaning the main control board has lost contact with the lower inverter module. The inverter is responsible for controlling motor-driven functions within the oven system, and it communicates continuously with the control board. When that communication signal is absent for more than 25 seconds, the oven halts operation entirely to prevent damage to components or unsafe operating conditions.

The three primary causes of this fault are a loss of AC power to the inverter, a disconnected or damaged wiring connector, or a blown fuse. Specifically, fuse F2 is the protection fuse associated with this circuit, and if it has opened due to a surge or overload, the inverter will not receive power and cannot transmit its status signal. Connectors J1 and J2 on the PMACS (Power Module and Control System) board are the interface points between the control system and the inverter, and either connector being loose, corroded, or physically damaged will produce the same communication failure.

Diagnostic work should begin by confirming that AC voltage is present at the inverter power supply terminals. If voltage is confirmed, inspect connectors J1 and J2 for secure seating, bent pins, or signs of heat damage. If the connectors are intact, check fuse F2 for continuity using a multimeter. A blown fuse may indicate an underlying overcurrent condition that should be investigated before simply replacing the fuse and resuming operation.

Source: manufacturer service documentation.

Common causes of Fd13

  1. 01

    Blown Fuse F2

    Part replacement

    Fuse F2 protects the inverter power supply circuit. If it has blown due to a power surge or overcurrent event, the inverter loses power entirely and cannot communicate with the control board. Check F2 for continuity with a multimeter.

  2. 02

    Loose or Disconnected Connector J1 or J2

    Wiring / connection

    Connectors J1 and J2 on the PMACS board link the control system to the lower inverter. If either connector has come loose or been pulled free, the communication signal will be lost. Inspect both connectors for secure seating and physical damage.

  3. 03

    Damaged Wiring or Connector Pins

    Part replacement

    Corrosion, heat stress, or physical damage to the wiring harness between the PMACS board and the inverter can interrupt the communication signal. Look for burnt insulation, bent or broken pins, or signs of arcing at J1 and J2.

  4. 04

    Loss of AC Power to the Inverter

    Wiring / connection

    If the inverter is not receiving its required AC supply voltage, it cannot operate or send a status signal. Confirm that AC voltage is present at the inverter power input terminals before moving on to other components.

  5. 05

    Failed Lower Inverter Module

    Part replacement

    If power is confirmed at the inverter, fuse F2 is intact, and connectors J1 and J2 are secure and undamaged, the inverter module itself may have failed internally and require replacement.

See the test procedure for each cause

Frequently asked questions about Fd13

What does Fd13 mean on a Electrolux oven?
Fd13 is a Lower Inverter Communication Error. It means the oven's control board has not received a communication signal from the lower inverter module for more than 25 seconds. The oven stops operation when this fault is detected. The most common causes are a blown fuse F2, a disconnected connector at the PMACS board, or a loss of AC power to the inverter.
Can I fix the Fd13 error myself?
Some causes of Fd13 are accessible to a knowledgeable DIYer, such as reseating loose connectors J1 and J2 or replacing a blown fuse F2. However, working inside an oven involves exposure to high-voltage AC components, so the appliance must be fully unplugged before any inspection. If the inverter module itself has failed, replacement typically requires identifying the correct part and some comfort with disassembly, or a qualified technician should be called.
Is it safe to use my Electrolux oven while it shows the Fd13 error?
No. The Fd13 error causes the oven to stop operation automatically, and it should not be used until the fault is resolved. Continuing to attempt operation with a communication or power failure in the inverter circuit could risk further component damage. Have the fault diagnosed and repaired before using the oven again.
Will resetting the oven clear the Fd13 error?
A power reset by unplugging the oven or cycling the breaker may temporarily clear the displayed error code, but it will return if the underlying cause is not addressed. Because the fault triggers after the communication signal is missing for more than 25 seconds, any condition that disrupts inverter power or the connector signal will cause Fd13 to reappear during the next operating cycle.
How much does it cost to repair an Electrolux oven with an Fd13 error?
Repair costs vary depending on the root cause. Replacing fuse F2 is typically inexpensive, with parts costing a few dollars to around $15 to $25 if a service call is involved. If a wiring harness or connectors need repair, labor costs can range from $75 to $150 or more. Replacing the lower inverter module is the most expensive scenario, with parts and labor potentially ranging from $150 to $400 or higher depending on parts availability and service rates in your area.

Related Electrolux oven codes

All Electrolux oven codes
View all 186 Electrolux oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass