Model reference

Fisher & Paykel WL4027P1

Washer

1 document62 error codes7 service modes

Available documentation

Service Manual

Service Manual AQUASMART Hi-Efficiency washer80 pg
Covers this model

MyPros+ Max

Diagnose your Fisher & Paykel WL4027P1.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Fisher & Paykel Washer

1 on my Fisher & Paykel WL4027P1

M+

Motor Control Module has encountered an

From Service Manual 407850, p.22:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure drive motor winding resistance. Expected: 2 to 6 ohms between winding pairs.

3.Rotate the drum by hand. Inspect the belt and pulley for glaze or wear.

Part W10006384

Drive motor

Error codes (62)

CodeMeaning

1Motor Control Module has encountered an error when writing to an EEPROM address.10Temperature sensor (thermistor) may be open circuit.103Slave display comms timeout.104Slave display comms timeout.105Comms error timeout 106Display Module to Motor Control Module communications error.107Motor Control Module reset error 108Comms CRC error between Display Module and Motor Control Module.112Motor current sense circuit is faulty; current sense too high.114Smart pump current sense circuit within the motor control module is faulty.12Flood protection error 133Repetitive current trip 136Motor stall 137Motor loss of a phase 16Motor controller has detected that the display type has not been set.160Basket engaged in agitate 21Water valve circuit is drawing too high a current.220EEPROM model map not programmed 221Motor Control Module RAM check error.222Motor Control Module stack error.223Motor Control Module program counter error.224Motor Control Module peripheral error.225Motor Control Module clock error.226MarchX RAM check error in Motor Control Module.230EEPROM value out of range 232COMMS timeout 5 seconds 233EEPROM read error 234Lid lock open circuit detected.235Lid lock short circuit 236Incompatible EEPROM version

View all 62 error codes

237Temperature sensor error 238Lid lock open circuit.239Lid lock short circuit.241Function time out 243Stepper test failure 245Smart pump stall 246Wash boost / bleach valve fault 247Smart pump flapper fault 248SmartPump top up fault 249SmartPump timeout fault 250SmartPump loss of sync 252Bridge test failure 253Smart pump over current 254Motor Control Module software version is too old for the display to support.26Detergent valve is faulty; valve harness not connected correctly or valve is…27Fabric softener valve is faulty; valve harness not connected correctly or valve…36Water leak fault 37No change in water level (pump blocked error)38Pressure sensor fault 39Pressure tube fault detected by Motor Control Module.40Basket dis-engage fault 41Temperature sensor fault 45Display memory check fault 46Display has detected a problem with its internal EEPROM.49Cold valve or both cold and hot valves are open circuit, detected via valve…50Hot valve coil is faulty; valve harness not connected correctly or valve is…56Basket check no valid fault 57Brown out during display EEPROM write 58Pressure transducer at maximum adjustment 60Motor Control memory check fault 68Pressure transducer error 9The Motor Control Module has found a fault with the size setting.

Service modes (7)

Customizing Mode1
Diagnostic Mode (Hi Spec Model)1
Diagnostic Mode (Mid Spec Model)1
Display Type Setting1
Installation Test1
Preset Options Adjustment Mode1
Showroom Mode (Hi Spec Model)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Fisher & Paykel washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass