Model reference

Fisher & Paykel WL37T27DW2

Washer

1 document58 error codes12 service modes

Available documentation

Service Manual

Service Manual AQUASMART™ Hi-Efficiency washer79 pg
Covers this model

MyPros+ Max

Diagnose your Fisher & Paykel WL37T27DW2.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Fisher & Paykel Washer

1 on my Fisher & Paykel WL37T27DW2

M+

Motor Control Module has encountered an

From Service Manual 766606, p.18:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure drive motor winding resistance. Expected: 2 to 6 ohms between winding pairs.

3.Rotate the drum by hand. Inspect the belt and pulley for glaze or wear.

Part W10006384

Drive motor

Error codes (58)

CodeMeaning

1Motor Control Module has encountered an error when writing to an EEPROM address.10Temperature sensor (thermistor) may be open circuit.104See fault code 106 105Comms error time out 106Display Module to Motor Control Module communications error.107Motor Control Module reset error 108Comms CRC error 110Motor bridge thermistor open circuit.111Motor bridge thermistor short circuit.112Motor current sense too high 113AC pump thermistor short circuit.12Flood protection error 130Rotor Position Sensor error 136Motor stall 160Basket engaged in agitate 220EEPROM model map not programmed 230EEPROM value out of range 232COMMS timeout 5 sec 233EEPROM read error 234Lid lock open circuit.235Lid lock short circuit 236Incompatible EEPROM version 237Temperature sensor error 238Lid lock open circuit 24Dispensing type not set in the Motor Control Module.240Hall out of order / RPS fault 241Function time out 243Stepper test failure 245SmartPump stall 246Bleach valve fault

View all 58 error codes

247SmartPump flapper fault 248SmartPump top up fault 249SmartPump timeout fault 250SmartPump loss of sync 252Bridge test failure 254Motor Control version too old 26Detergent valve (purple clip) fault 27Fabric softener valve (yellow clip) fault 3Motor Control Module has found a memory error.36Water leak fault 37Pump blocked error 38Pressure sensor fault 39Pressure tube fault 40Basket dis-engage fault 41Temperature sensor fault (thermistor)45Display memory check fault 46Display memory EEPROM check 48Hot and cold valve coils faulty 49Cold valve coil faulty 50Hot valve coil faulty 56Basket check no valid fault 57Brown out during display EEPROM write 60Motor control memory check fault 68Pressure transducer error 69Pressure transducer error 70Pressure transducer error 72Pressure transducer error 9The Motor Control Module has found a fault with the size setting.

Service modes (12)

Component Test Mode - LCD Model (Machine Status Screen)1
Component Test Mode - LED Model1. Enter Diagnostic Mode (press and hold HI EFFICIENCY button, then press POWER button until two…
Data Download - LCD Model1
Data Download - LED Model1
Diagnostic Mode - LCD Model1
Diagnostic Mode 1 - LED Dispensing Model1
Diagnostic Mode 2 - LED Non-Dispensing Model1
Dispensing Type Setting - LCD Model1
Dispensing Type Setting - LED Model1. Turn power on at power point and off at console. 2. Ensure no LEDs are lit. 3. Press and hold…
Fault Code Display - LED Model1
Showroom Mode - LCD Model1
Showroom Mode - LED Model1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Fisher & Paykel washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass