Samsung WA48H7400AW

Model reference

Samsung WA48H7400AW

Washer

3 documents55 error codes2 service modes

Available documentation

Service Manual

Washing Machine (Top-loading) Service Manual37 pg
Covers this model
WASHING MACHINE (TOP-LOADING) SERVICE Manual35 pg
Covers this model

Other

LG Samsung WA48H7400AP WA48H7400AP A2 SM35 pg
Covers this model

MyPros+ Max

Diagnose your Samsung WA48H7400AW.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (55)

CodeMeaning

1CWater level sensor fault due to damaged, clogged, or folded hose, excessive…1EWater Level Sensor Trouble 3CMotor driving check and hall sensor check 3EMICOM is attempting to drive the motor but is not getting any response signals…4CWater supply check 4C2Water temperature sensed higher than 70°C during dry cycle through dry valve…4EFilling continues for more than 60 minutes or there is no change of water level…4E2The hot/cold water hose connection is not correct.5CDrain check 5EThe water level fails to drop below the Reset Water Level within 30 minutes…8CClutch motor error 8C1MEMS PBA check detected 8C2MEMS PBA check 8EOutput from the MEMS sensor is over 4.5V or under 0.5V continuously for 5…8E1Output from the MEMS sensor is over 4.5V or under 0.5V continuously for 5…8E2Output from the MEMS sensor is over 4.5V or under 0.5V continuously for 5…9C1Power check 9C2Power check ACCommunication check AC2Communication check between the DR Module and main PBAs AC3Communication check between the WIFI Module and main PBAs AC4Communication check between the LCD Module and main PBAs AC5Communication check between the Inverter PBA and main PBA AC6Communication check between sub and main PBAs AECommunication error between SUB PBA and MAIN PBA.BC2Switch check (Main Relay Check)bE2A button except the Power button is continually pressed.DCDoor check DC1Door check DC2Door check

View all 55 error codes

dEDoor is detected as open while the unit is trying to lock the door.dE1Door fails to unlock after 7 attempts.HCHeater check HC1Washing heater in the tub has a contact fault or temperature sensor fault; if…HC2Drying heater is short-circuited or has a wire disconnected.LCWater leakage check LC1Water leakage check LEA water level lower than the Reset water level is detected for 5 seconds during…OCOverflow check OEWater level sensor data (frequency) shows the water level is at or above the…PCClutch motor error PC1Clutch sensor error PEClutch Motor Error PE1Clutch Motor Error SdSuds is detected during the washing session (alternate display of Sud; not a…SF1System check SF2System check SF3System check SudSuds is detected during the washing session (not a true error; when washing…TC1Temperature sensor check TC2Temperature sensor check TC4IPM temperature is abnormally high.tEWater temperature sensor fault is detected continuously for 5 seconds.UBUnbalance check UEUnbalance or cabinet bump is detected during final spin.

Service modes (2)

Board Input TestReferenced in troubleshooting for checking Water Temperature; specific button entry sequence not…
Quick Test ModeReferenced in troubleshooting for Door Lock/Unlock Test and Motor Test; specific button entry…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Samsung washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass