mypros+
Error code reference

Maytag Dryer Error Code CHECK CONTROL BOARD FUSE #2

Main fuse (fuse 2) on the Phase 7 control board has opened; 24V control power fuse rated at 5-amps.

Maytag codesMaytag dryer codes

Main fuse (fuse 2) on the Phase 7 control board has opened; 24V control power fuse rated at 5-amps.

First step from the service manual

Check and replace fuse 2 on control board (5-amp, 24V control power fuse); investigate cause of fuse failure.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for CHECK CONTROL BOARD FUSE #2.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What CHECK CONTROL BOARD FUSE #2 means on a Maytag dryer

The CHECK CONTROL BOARD FUSE #2 error on a Maytag dryer indicates that fuse 2 on the Phase 7 control board has opened, cutting off the 24-volt control power circuit. This is a 5-amp fuse responsible for supplying low-voltage control power to the board's logic and relay circuits. When this fuse blows, the control board loses its ability to regulate dryer functions, triggering the error code and halting normal operation.

A blown fuse on the control board is never a random event. Something in the 24V control circuit drew enough current to exceed the 5-amp rating and cause the fuse to open. Common culprits include a short circuit in a component wired to the control circuit, a failing relay on the board itself, damaged wiring harness insulation causing a short to ground, or a defective door switch or other low-voltage input component pulling excessive current.

Diagnosing this error requires physically inspecting and replacing fuse 2 on the Phase 7 control board. However, simply replacing the fuse without identifying what caused it to blow will likely result in the new fuse opening again. Technicians should inspect the wiring harness for chafing or burnt insulation, test components connected to the 24V circuit for shorts, and examine the control board itself for visible burn marks or damaged traces before restoring power.

Source: manufacturer service documentation.

Common causes of CHECK CONTROL BOARD FUSE #2

  1. 01

    Short circuit in a 24V control circuit component

    Part replacement

    A component connected to the 24V control circuit, such as a door switch, sensor, or relay, may have developed an internal short, causing excessive current draw that exceeded the 5-amp fuse rating. Testing each connected component for shorts will help isolate the fault.

  2. 02

    Damaged or shorted wiring harness

    Part replacement

    Wiring insulation that has chafed against the dryer cabinet, drum, or other components can expose bare conductors that short to ground or to each other. Inspect the harness routing throughout the dryer for burnt, melted, or pinched wire sections.

  3. 03

    Faulty relay on the control board

    Part replacement

    A relay on the Phase 7 control board that has failed internally can create an overcurrent condition in the 24V circuit. Visible burn marks or a pitted relay contact on the board surface can help confirm this as the cause.

  4. 04

    Defective control board

    Part replacement

    If no external wiring or component faults are found, the Phase 7 control board itself may have an internal fault causing the fuse to open. Inspect the board for burnt traces, damaged components, or discoloration near the fuse location.

  5. 05

    Fuse fatigue from age or repeated overcurrent events

    Part replacement

    In some cases, a fuse that has experienced repeated marginal overcurrent events over time can become fatigued and open without a major fault present. If all connected components and wiring test within spec, replacing the fuse and monitoring for recurrence is appropriate.

See the test procedure for each cause

Frequently asked questions about CHECK CONTROL BOARD FUSE #2

What does CHECK CONTROL BOARD FUSE #2 mean on a Maytag dryer?
This error means that fuse 2 on the Phase 7 control board has blown open. Fuse 2 is a 5-amp fuse that supplies 24-volt control power to the board. When it opens, the control board loses power and the dryer will not operate. The fuse must be replaced and the root cause of the failure must be identified before the dryer is returned to service.
Can I fix the CHECK CONTROL BOARD FUSE #2 error myself?
Replacing the fuse itself is a straightforward task for someone comfortable working with appliance electronics, but the critical step is finding what caused the fuse to blow. If you replace the fuse without addressing the underlying fault, the new fuse will likely blow again. A thorough inspection of the wiring harness and all components connected to the 24V circuit is necessary before powering the dryer back on.
Will resetting my Maytag dryer clear the CHECK CONTROL BOARD FUSE #2 error?
No, a simple reset will not clear this error or restore dryer function. The fuse 2 on the control board is a physical component that must be replaced once it has opened. Resetting the control board does not restore a blown fuse, and the dryer will remain inoperable until the fuse is replaced and any contributing fault is corrected.
Is it safe to use my dryer when the CHECK CONTROL BOARD FUSE #2 error is showing?
The dryer will not operate while this error is active, so there is no immediate risk of using it. However, you should not attempt to bypass the fuse or operate the dryer without resolving the error. The fuse blew for a reason, and running the dryer without identifying that cause could result in damage to the control board or a wiring fault that poses a greater safety risk.
How much does it cost to fix the CHECK CONTROL BOARD FUSE #2 error on a Maytag dryer?
If only the fuse needs to be replaced, the part cost is very low, typically a few dollars, though labor charges for a service call will add to the total. If the underlying fault has damaged the Phase 7 control board and a full board replacement is needed, costs can range from roughly 150 to 400 dollars or more depending on parts and labor rates in your area. Identifying the root cause early helps avoid the cost of replacing a new fuse or board only to have the problem recur.

Related Maytag dryer codes

All Maytag dryer codes
View all 251 Maytag dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass