mypros+
Error code reference

Maytag Dryer Error Code dSFL

Temperature sensor connection fault displayed when power is reestablished after sensor probe replacement.

Maytag codesMaytag dryer codes

Temperature sensor connection fault displayed when power is reestablished after sensor probe replacement.

First step from the service manual

Check for loose connection on the wiring.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for dSFL.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What dSFL means on a Maytag dryer

The dSFL error code on a Maytag dryer indicates a temperature sensor connection fault. This code is specifically triggered when power is restored to the dryer after a temperature sensor probe has been replaced, and the control board detects an issue with the sensor circuit rather than a valid signal from the newly installed component. The control board monitors the resistance or voltage signal coming from the temperature sensor to verify proper installation and continuity before allowing normal operation to resume.

The most likely origin of this fault is a loose or improperly seated wiring connection at the sensor probe itself or at the control board connector. When a sensor probe is replaced, the harness connector must be fully engaged and locked into position. A partially inserted connector, a bent terminal pin, or a connector that was not re-secured after the repair can all produce an open or intermittent circuit that registers as a connection fault rather than a valid temperature reading.

Secondary causes include a defective replacement sensor that was damaged during installation, a wiring harness that was pinched or stressed during reassembly, or corrosion on the connector terminals that prevents reliable electrical contact. Because the fault is tied to the moment power is reestablished following a sensor replacement, it strongly points to something disturbed during the repair process rather than a pre-existing failure in unrelated components.

Source: manufacturer service documentation.

Common causes of dSFL

  1. 01

    Loose or improperly seated wiring connector

    Wiring / connection

    After sensor probe replacement, the wiring harness connector may not have been fully clicked into place. Inspect the connector at the sensor and confirm it is completely seated and locked.

  2. 02

    Bent or damaged terminal pin

    Wiring / connection

    During removal or reinstallation of the connector, a terminal pin inside the connector housing can become bent or pushed back, breaking the electrical contact. Visually inspect each pin for proper alignment and position.

  3. 03

    Defective replacement sensor probe

    Part replacement

    The new sensor may have been damaged during shipping or installation, resulting in an open circuit that the control board interprets as a connection fault. Testing the sensor for proper resistance with a multimeter can confirm or rule this out.

  4. 04

    Pinched or damaged wiring harness

    Part replacement

    Reassembly of the dryer cabinet after the sensor replacement may have pinched the sensor wiring harness against a sharp edge or component, causing an open or short circuit. Trace the harness from the sensor to the control board connector looking for visible damage.

  5. 05

    Corroded or contaminated connector terminals

    Wiring / connection

    If the connector terminals have corrosion or debris on them, electrical contact between the harness and the sensor can be unreliable. Cleaning the terminals with electrical contact cleaner and reconnecting firmly may resolve the fault.

See the test procedure for each cause

Frequently asked questions about dSFL

What does dSFL mean on a Maytag dryer?
The dSFL code on a Maytag dryer indicates a temperature sensor connection fault. It appears when power is restored after a temperature sensor probe replacement and the control board cannot detect a valid signal from the sensor. The code points to a problem in the sensor circuit, most often a loose or improperly connected wiring harness.
How do I fix the dSFL error on my Maytag dryer?
Start by unplugging the dryer and locating the temperature sensor wiring connector. Disconnect and firmly reseat the connector, confirming it clicks fully into place. If the error returns after restoring power, inspect the connector terminals for damage or corrosion and verify the replacement sensor itself is functioning correctly with a multimeter.
Will resetting my Maytag dryer clear the dSFL error code?
A simple power reset is unlikely to permanently clear the dSFL code if the underlying wiring connection issue has not been corrected. The fault is tied to a sensor circuit problem detected at power-up, so it will typically return until the loose or faulty connection is physically repaired. Fix the connection first, then restore power to confirm the code is gone.
Is it safe to use my Maytag dryer when the dSFL code is displayed?
It is not advisable to operate the dryer while the dSFL error is active. The temperature sensor is a critical safety component that allows the control board to monitor heat levels during a cycle. Without a reliable sensor signal, the dryer cannot properly regulate temperature, which could lead to overheating or incomplete drying cycles.
How much does it cost to repair the dSFL error on a Maytag dryer?
If the fix only requires reseating a loose wiring connector, there is no parts cost involved. If the replacement temperature sensor is defective and needs to be swapped again, sensor parts typically range from $15 to $40 depending on the model. Adding professional labor for diagnosis and repair can bring the total to somewhere in the range of $75 to $175.

Related Maytag dryer codes

All Maytag dryer codes
View all 251 Maytag dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass