mypros+
Error code reference

Maytag Dryer Error Code F-9

Low voltage (below about 95 volts); dryer will operate and fault code is not displayed unless checked via…

Maytag codesMaytag dryer codes

Low voltage (below about 95 volts); dryer will operate and fault code is not displayed unless checked via special procedure.

First step from the service manual

Press OFF pad and while holding OFF pad, press the PAUSE/RESUME pad and hold for 2 seconds to check; then check electrical circuit that dryer is on.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F-9.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F-9 means on a Maytag dryer

The F-9 error code on a Maytag dryer indicates that the supply voltage has dropped below approximately 95 volts AC. This is a low voltage condition, meaning the dryer is receiving insufficient electrical power from the home's supply circuit. Electric dryers typically require 240 volts (delivered across two 120-volt legs) to operate correctly, while gas dryers require a stable 120-volt supply. When voltage falls below the threshold, the control board detects the abnormal supply condition and logs the fault internally.

Unlike many fault codes that halt operation and display immediately, the F-9 code is passive. The dryer may continue to run in a degraded state, but the code will not appear on the display during normal use. To retrieve it, a technician must access the fault history through a specific key sequence: press and hold the OFF pad, then while holding it, press and hold the PAUSE/RESUME pad for two seconds. This procedure reveals stored fault codes that were logged during operation.

The root cause is almost always in the home's electrical supply circuit rather than in the dryer itself. Possible sources include a failing or undersized circuit breaker, a loose or corroded neutral or hot connection at the outlet, a weak leg at the main electrical panel, or an overloaded circuit. Shared circuits, long wiring runs with undersized wire gauge, and aging electrical infrastructure are all contributing factors. Because low voltage can cause motor and heating element stress over time, identifying and correcting the supply issue promptly is important.

Source: manufacturer service documentation.

Common causes of F-9

  1. 01

    Loose or corroded outlet connection

    Part replacement

    A loose wire connection at the dryer's wall outlet or terminal block can cause voltage to drop under load. Inspect the outlet for burnt contacts, loose terminals, or discoloration that indicates heat damage.

  2. 02

    Failing or tripped circuit breaker leg

    Part replacement

    A double-pole breaker with one weak or partially tripped leg can deliver reduced voltage to the dryer. Check the breaker panel for a breaker that feels loose, shows heat damage, or does not reset firmly.

  3. 03

    Loose connection at the main electrical panel

    Wiring / connection

    Loose or oxidized wiring connections at the panel where the dryer circuit originates can create a voltage drop under load. This requires inspection by a licensed electrician.

  4. 04

    Undersized or overloaded circuit wiring

    Wiring / connection

    If the dryer circuit uses wire gauge that is too small for the load, or if the circuit is shared with other high-draw appliances, voltage can sag below acceptable levels during operation.

  5. 05

    Utility supply voltage issue

    Wiring / connection

    Broader utility voltage problems such as a weak service entrance, a failing utility transformer, or a storm-related supply issue can reduce incoming voltage to the home. A multimeter reading at the outlet during dryer operation can confirm whether the problem is upstream of the home's panel.

See the test procedure for each cause

Frequently asked questions about F-9

What does F-9 mean on a Maytag dryer?
F-9 on a Maytag dryer means the control board detected supply voltage below approximately 95 volts. This is a low voltage fault that is stored in the dryer's fault history but does not display automatically during normal operation. To see it, you must hold the OFF pad and then press and hold PAUSE/RESUME for two seconds. The issue is typically in the home's electrical circuit, not the dryer itself.
How do I fix the F-9 error code on my Maytag dryer?
Start by checking the dryer's wall outlet and power cord connections for looseness, corrosion, or heat damage. Next, inspect the circuit breaker in your electrical panel to confirm both legs of the double-pole breaker are firmly seated and functioning. If the outlet and breaker appear normal, have a licensed electrician check the panel connections and the incoming service voltage, especially under load.
Will resetting the dryer clear the F-9 code?
Resetting the dryer may clear the stored fault code temporarily, but the F-9 will return if the underlying low voltage condition is not corrected. Because the code is stored rather than actively displayed, simply cycling power does not address the root cause. The electrical supply circuit must be inspected and repaired to prevent the fault from logging again.
Is it safe to keep using my Maytag dryer with an F-9 code?
Continuing to run the dryer with a low voltage condition can put stress on the motor and heating components over time, potentially shortening their lifespan or causing additional failures. There is also a risk that the underlying electrical issue, such as a loose connection, could worsen and create a fire or shock hazard. It is best to identify and correct the voltage problem before continued use.
How much does it cost to fix a Maytag dryer F-9 error?
If the problem is a faulty wall outlet or power cord, repair costs are typically in the range of $50 to $150 depending on parts and labor. If a circuit breaker needs replacement, expect $75 to $200 including an electrician's service call. Issues at the main panel or utility service entrance can range from $150 to $400 or more depending on the complexity of the repair and local labor rates.

Related Maytag dryer codes

All Maytag dryer codes
View all 251 Maytag dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass