mypros+
Error code reference

Maytag Dryer Error Code dC

Dryer motor control circuit error (cycles and customer display disabled until diagnostic code is manually…

Maytag codesMaytag dryer codes

Dryer motor control circuit error (cycles and customer display disabled until diagnostic code is manually cleared).

First step from the service manual

Check motor circuit and harness connections.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for dC.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What dC means on a Maytag dryer

The dC error code on a Maytag dryer indicates a fault in the motor control circuit. This code signals that the control board has detected an abnormal condition within the circuit responsible for powering and regulating the drive motor. When this fault is triggered, the dryer disables normal cycle operation and locks the customer display until the diagnostic code is manually cleared by a technician or knowledgeable user. The dryer will not resume standard operation until the underlying fault is resolved and the code is cleared.

The motor control circuit includes the drive motor itself, the associated wiring harness, connectors, the motor start relay or capacitor (depending on configuration), and the control board that interprets motor feedback signals. A fault in any of these components can cause the control board to register a dC condition. The most common entry points for this fault are loose or corroded connector pins at the motor harness, a failed motor winding, or a control board that is not receiving proper continuity signals from the motor circuit.

Diagnostic work should begin with a thorough inspection of the motor circuit wiring harness and all related connectors, checking for damaged insulation, pin corrosion, or loose terminal seats. If the harness checks out, the drive motor itself should be tested for proper winding resistance and continuity. If both the harness and motor test within acceptable parameters, the control board may be the source of the fault, as it is responsible for processing the motor circuit feedback and triggering the dC code when something falls outside expected operating parameters.

Source: manufacturer service documentation.

Common causes of dC

  1. 01

    Loose or damaged motor harness connections

    Wiring / connection

    Connector pins at the drive motor can become loose, corroded, or unseated over time, interrupting the motor control circuit signal. Inspect all harness connectors at the motor for secure seating, corrosion, and damaged terminals.

  2. 02

    Failed drive motor

    Part replacement

    The drive motor windings can fail due to overheating or normal wear, causing an open or short in the motor control circuit. Testing the motor for proper continuity and winding resistance will confirm this fault.

  3. 03

    Damaged wiring harness

    Part replacement

    Chafed, pinched, or broken wires along the motor harness can interrupt the circuit and trigger the dC code. A visual inspection along the full harness routing will often reveal the damage point.

  4. 04

    Faulty motor control board

    Part replacement

    If the wiring harness and motor both test correctly, the control board itself may have failed and is incorrectly reading or processing the motor circuit signals. This is typically diagnosed after ruling out all other components.

  5. 05

    Tripped thermal overload or motor protector

    Wiring / connection

    Some drive motors include an internal thermal overload protector that can trip under sustained high temperature conditions and disrupt the motor circuit. If the motor has been overloaded, this protector may need time to reset or may need replacement.

See the test procedure for each cause

Frequently asked questions about dC

What does dC mean on a Maytag dryer?
The dC code on a Maytag dryer indicates a motor control circuit error. The control board has detected a fault in the circuit responsible for powering or regulating the drive motor. When this code is active, all normal cycles and the customer display are disabled until the code is manually cleared. The dryer will not operate until the fault is diagnosed and resolved.
Can I fix the dC error code myself?
Some causes of the dC code, such as loose or disconnected harness connectors, can be addressed by a confident DIYer with basic electrical knowledge. Start by unplugging the dryer and inspecting all wiring connections at the motor for looseness or corrosion. However, if the motor or control board has failed, replacing those components typically requires more advanced repair skills and proper diagnostic tools.
Is it safe to use my Maytag dryer when the dC code is showing?
No. When the dC code is active, the dryer intentionally disables all cycle operation to prevent the machine from running with a compromised motor circuit. Attempting to bypass or override this condition is not recommended, as motor circuit faults can present electrical hazards or cause further damage to components.
Will resetting the dryer clear the dC code?
A simple power reset, such as unplugging the dryer or cycling the breaker, is unlikely to permanently clear the dC code if the underlying fault still exists. The code is designed to remain active until it is manually cleared through a diagnostic procedure, and it will typically return if the root cause in the motor circuit has not been corrected.
How much does it cost to repair a Maytag dryer with a dC error code?
Repair costs vary depending on which component has failed. If only a harness connector or wire needs repair, costs may be minimal. Replacing a drive motor typically costs in the range of $150 to $350 including parts and labor, while a control board replacement can range from $200 to $450 or more depending on the model and service rates in your area.

Related Maytag dryer codes

All Maytag dryer codes
View all 251 Maytag dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass