Model reference

GE GFW650SSN3WW

Washer

1 document74 error codes2 service modes

Available documentation

Service Manual

UltraFresh Front Load Washer Service Guide100 pg
Covers this model

MyPros+ Max

Diagnose your GE GFW650SSN3WW.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·GE Washer

1 on my GE GFW650SSN3WW

M+

Lock Monitor – Motor shaft speed

From Service Manual 841968, p.20:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure door lock assembly resistance across PTC terminals. Expected: ~200 ohms cold.

3.Inspect strike and latch alignment. A misaligned strike prevents the switch stack from closing.

Part WH44X10288

Door lock assembly

Error codes (74)

CodeMeaning

1Lock Monitor 14Bluetooth Communication Pairing Failure 15Water Temp Sensor Invalid 16Bluetooth Communication Pairing Failure 17Dry Load Sense Timeout 18Drain Pump Clearing Algorithm Failed 19UI State Timeout 2Door Monitor 20Critical Flood Level by Gallons 22Out of Balance (OOB) During Dry Load Sense 23Critical Door Lock Failure 24Door Logic Failure 25Pressure Sensor Dropout / Pressure Sensor Continuous Gallons Monitor 26Out of Balance (OOB) Ended Final Spin 27Water Accessibility 29Suds Lock Abatement Failure 3Locked Rotor Monitor 30Stuck Button Fault 31Out of Balance (OOB) Ended Final Spin 32Critical Door Lock Failure: Can't Unlock Door, Inverter Power and Door Lock…33Inverter Fault 34Inverter Fault 35Accelerometer Fault 37Heater Fault 38Vent Damper Fault 39Vent Damper Fault 40Vent Damper Fault 41Inverter Fault 42Inverter Fault 43Inverter Fault

View all 74 error codes

44Inverter Fault 45Inverter Fault 46Inverter Fault 47Inverter Fault 48Inverter Fault 49Inverter Fault 50Inverter Fault 51Inverter Fault 57Door Lock Fault Water Above Door by Pressure 58Main Board Component Failure 59Accelerometer Fault 6Critical Flood Level by Pressure 60Accelerometer Fault 61Accelerometer Fault 62Inverter Power And Door Lock Monitor 63Accelerometer Fault 64Accelerometer Fault 65Pressure Sensor Dropout / Pressure Sensor Continuous Gallons Monitor 66Inverter Fault 67Inverter Fault 68Inverter Fault 69Inverter Fault 70Inverter Volt/Hertz Start Up 71Inverter Fault 72Inverter Fault 73Inverter Fault 74Inverter Fault 77Critical Door Lock Failure: Can't Unlock Door, Inverter Power and Door Lock…78Board Communication API Mismatch 8Pressure Sensor Loss 80Humidity/Temperature Board Failure 81Humidity/Temperature Board Heartbeat Failure 83Inverter Fault 84Vent Damper Fault 87Accelerometer Fault 88Accelerometer Fault 89Accelerometer Fault 9Door Switch Redundancy 90Accelerometer Fault 91UI - Main Board Heartbeat Timeout 92Inverter Fault 93Main Board Component Failure 94Water Quality Sensor (Turbidity Sensor) Fault 98Humidity Sensor I2C Communication Failure

Service modes (2)

Consumer Fault Code ModeFrom an idle state only (all LEDs off), press and hold Start pad for 10 seconds
Service ModePress and hold Start pad while rotating the cycle selection knob seven clicks, then release the…

Full entry steps, exit procedures, and test sequences are available in Max.

Related GE washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass