Model reference

Fisher & Paykel IWL12

Washer

8 documents109 error codes25 service modes

Available documentation

Service Manual

ELECTRONIC WASHING MACHINE GWL11 / IWL12 PHASE 6 Series 11 / 12 120v 60Hz Supplementary manual47 pg
Covers this model
Smart Drive Electronic Washing Machine Model GWL11 IWL12 51775319 pg
Covers this model
ELECTRONIC WASHING MACHINE GWL11 / IWL12 PHASE 6 Series 11 / 12 120v 60Hz47 pg
Covers this model
Smart Drive Electronic Washing Machine25 pg
Covers this model

Tech Sheet

Service Summary GWL11 / IWL124 pg
Covers this model

Bulletin

Service Bulletin - Unable to Fit Motor Control Module 420094USP1 pg
Covers this model
Smart Drive Electronic Module Summary Phases 3 - 6 USA5 pg
Covers this model

Installation Guide

IWL12 Clothes Washer Installation Instructions and User Guide80 pg
Covers this model

MyPros+ Max

Diagnose your Fisher & Paykel IWL12.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Fisher & Paykel Washer

#130 on my Fisher & Paykel IWL12

M+

Rotor Position Sensor error – a faulty

From Service Manual 382164, p.16:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure drive motor winding resistance. Expected: 2 to 6 ohms between winding pairs.

3.Rotate the drum by hand. Inspect the belt and pulley for glaze or wear.

Part W10006384

Drive motor

Error codes (109)

CodeMeaning

#130Rotor Position Sensor error #131Rotor Position Sensor error #132High motor current #133High motor current #136Motor stall #37Pump blocked error #39Pressure tube fault #40Basket disengage fault #43Out of balance switch fault #47Lid lock fault.#48Hot and/or cold water valve faulty.#49Hot and/or cold water valve faulty.#50Hot and/or cold water valve faulty.#51Diverter valve fault #52Diverter valve fault #9Machine size setting does not match that stored in memory.1Motor Controller Module (Display for Phase 1) has encountered an error when…10Temperature sensor (thermistor) may be open circuit or ambient temperature is…104Communications error between Display module and Motor Controller (Phase 2 to 6).105Comms error timeout 106Display to Motor Controller communications error.107Motor Controller module reset error 108Comms CRC error (Phase 6 IW Display only).11While measuring water level, the Motor Controller detected a negative pressure…12Flood protection error 127Machine setup error 13Pump fault 130Single rotor position sensor error 131Repetitive rotor position sensor error 132Single current trip

View all 109 error codes

133Repetitive current trip 134Single current trip and rotor position error simultaneously (Phase 4).136Motor stall 14Pump connection fault 144Motor Controller software trap 15Display Module has read an incorrect voltage on the pump circuit (Phase 1).160Basket engaged 161Hardware/EEPROM supply mismatch 162Brake deceleration timeout fault 163Valve reset pin connect fault 164Brake function timeout fault 17Display / Motor Controller running out of sequence (Phase 1).18Display / Motor Controller running out of sequence (Phase 1).19Display / Motor Controller running out of sequence (Phase 1).192Motor PMW reset pin connect fault 2An error has been encountered when trying to read the pressure sensor.20Display / Motor Controller running out of sequence (Phase 1).22Display / Motor Controller running out of sequence (Phase 1).23Display / Motor Controller running out of sequence (Phase 1).230EEPROM value out of range 231MW GW link error 232COMMS timeout 5 seconds 233EEPROM read error 234Lid lock open circuit 235Lid lock short circuit 236Incompatible EEPROM version 237Temperature sensor error 238Lid lock fail in-line test (1)239Lid lock fail in-line test (2)240Hall out of order / RPS fault 241Function timeout 242OOB hit greater than max for 5 seconds 243Stepper test failure 25LCD Initialisation Error 28Display / Motor Controller running out of sequence (Phase 1).29Display / Motor Controller running out of sequence (Phase 1).3Motor Controller Module has found a memory error.30Display / Motor Controller running out of sequence (Phase 1).32Pump circuit error 33Water valve fault 34Brake resistor fault 35MC Reset Error 36Water leak fault 37Pump blocked error 38Pressure sensor fault 39Pressure tube fault 4The Motor Controller has had difficulty communicating with the Display Module…40Bowl disengage fault 41Temperature sensor fault (thermistor)42Rotor fault 43OOB switch fault 44Water in tub during spin 45Display memory check fault 46Display EEPROM check 47Basket disengage fault 48Hot and cold valve faulty 49Cold valve (proportional) faulty 5The Display Module has had difficulty communicating with the Motor Controller…50Hot valve (digital) faulty 51Diverter valve fault 52Diverter top-up fault 53Rotor Position Sensor step fail 54Motor/Motor Controller module step fail 55System step fail (Phase 3 to 6).56Basket check no valid fault 57Brown out during Display EEPROM write 58Pressure transducer at maximum adjustment 59ID out of range fault 6Motor Controller module (Display for Phase 1) has received an incorrect signal…60Motor Control memory check fault 61Brown out during Motor Controller EEPROM write 62Pump over current 63Pump comms error 64Pressure transducer error 65Pressure transducer error 66Pressure transducer error (Ptx frequency >90 kHz)7Display module has found a memory fault.8Display micro has not been able to start up correctly (Phase 1 only).9Display size switch setting does not match that stored in memory.

Service modes (25)

Data Display Mode - IW1
Demonstration Mode - GWPress and hold the ADVANCE button, then press the POWER button.
Demonstration Mode - IWPress START/PAUSE and hold down, then press POWER.
Diagnostic Mode["Turn the power on at the power point and off at the console.","IWL12
Diagnostic Mode - GW (Ecosmart)1
Diagnostic Mode - IW (Intuitive)1
Drain Pump Test - GW1
Drain Pump Test - IW1
Drain Pump Test (within Diagnostic Mode)["Enter Diagnostic Mode.","IWL12
Hot Tub Flag Clear - GW1
Hot Tub Flag Clear - IW1
Machine Size Setting["Turn the power on at the power point and off at the console.","IWL12
Out Of Balance Switch Test (within Diagnostic Mode)["Enter Diagnostic Mode.","IWL12
Pump Pulse Disable - GW1
Recycle Feature - GW1
Recycle Feature - IW1
Restart Feature - GW1. Enter Diagnostics Mode (power off at machine, on at wall; press and hold Wash Temp Down then…
Restart Feature - IW1
Restart Feature Setting - GW1
Restart Feature Setting - IW1
Size Setting Mode - GW1
Size Setting Mode - IW1
Water Valve Test - GW1
Water Valve Test - IW1
Water Valve Test (within Diagnostic Mode)["Enter Diagnostic Mode.","IWL12

Full entry steps, exit procedures, and test sequences are available in Max.

Related Fisher & Paykel washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass