mypros+
Model reference

GE GFWN1600

Washer

4 documents103 error codes19 service modes

Available documentation

Service Manual

  • GE Appliances Front Load Washer Technical Service Guide70 pg
    Covers this model
  • Service Technician Only - Diagnostic Guide8 pg
    Covers this model
  • Technical Service Guide - UltraFresh Front Load Washer82 pg
    Covers this model
  • UltraFresh Front Load Washer Service Guide100 pg
    Covers this model
MyPros+ Max

Diagnose your GE GFWN1600.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (103)

CodeMeaning
0No faults present; displayed in Service Mode only when there are no faults to…1Lock Monitor14Bluetooth Communication Pairing Failure15Water Temp Sensor Invalid16Bluetooth Communication Pairing Failure17Dry Load Sense Timeout18Drain Pump Clearing Algorithm Failed19UI State Timeout2Door Monitor20Critical Flood Level by Gallons22Out of Balance (OOB) During Dry Load Sense23Critical Door Lock Failure24Door Logic Failure25Pressure Sensor Dropout26Out of Balance (OOB) Ended Final Spin27IMP Overheated29Drive System Self-Check Fault3Locked Rotor Monitor30Main Board Over Voltage31Main Board Self Check Failed32Critical Door Lock Failure: Can't Unlock Door33Inverter Fault34Inverter Fault35Accelerometer Fault37Heater Fault38Vent Damper Fault39Vent Damper Fault40Vent Damper Fault41Inverter Fault42Inverter Fault
View all 103 error codes
43Inverter Fault44Inverter Fault45Inverter Fault46Inverter Fault47Inverter Fault48Inverter Fault49Inverter Fault50Inverter Fault51Inverter Fault57Door Lock Fault Water Above Door by Pressure58ADC Health Check Fault59Accelerometer Fault6Critical Flood Level by Pressure60Accelerometer Fault61Accelerometer Fault62Inverter Power And Door Lock Monitor63Accelerometer Fault64Accelerometer Fault65Pressure Sensor Continuous Gallons Monitor66Inverter Fault67Inverter Fault68Inverter Fault69Inverter Fault70Inverter Volt/Hertz Start Up71Inverter Fault72Inverter Fault73Inverter Fault74Inverter Fault77Critical Door Lock Failure: Can't Unlock Door78Board Communication API Mismatch8Pressure Sensor Loss80Humidity/Temperature Board Failure81Humidity/Temperature Board Heartbeat Failure83Inverter Fault84Vent Damper Fault85Voltage Detected by MC is outside acceptable window.87Accelerometer Fault88Accelerometer Fault89Accelerometer Fault9Door Switch Redundancy90Accelerometer Fault91UI - Main Board Heartbeat Timeout92Inverter Fault93Main Board Component Failure94Water Quality Sensor (Turbidity Sensor) Fault98Humidity Sensor I2C Communication FailureE22Fill problem detected by the control.E23Fill problem detected by the control.E31Drain problem detected by the control.E38Dispenser mechanism problem detected.E39Dispenser mechanism problem detected.E42Motor drive operation above design limits.E45Motor drive operation above design limits.E46Motor drive operation above design limits.E47Motor drive operation above design limits.E48Motor drive operation above design limits.E4AMotor drive internal problem.E4BMotor drive internal problem.E4CMotor drive internal problem.E50Motor drive internal problem.E52Motor drive internal problem.E54Motor drive internal problem.E56Main control internal problem.E57Main control internal problem.E58Main control internal problem.E60Door lock assembly problem.E61Door lock assembly problem.E62System contact failure.E63Water level sensor problem.E64Water level sensor problem.E65Water level sensor problem.E66Water temperature sensor (thermistor) problem.E67Water temperature sensor (thermistor) problem.

Service modes (19)

  • Consumer Fault Code ModeFrom an idle state (all LEDs off), press and hold Start pad for 10 seconds
  • Control Board Programming (t01)1
  • Service ModePress and hold Start pad while rotating the cycle selection knob seven clicks, then release the…
  • Service Mode (Field Service Mode)Press and hold Start pad while rotating cycle selection knob 180 degrees, then release Start pad.
  • Service Test Mode1. Machine must be in idle mode (all LEDs on display off). 2. Press the following key sequence…
  • Service/Diagnostic ModeWithin 30 seconds of plugging in the washer, alternately press the Temp button and the Delay Wash…
  • t01 - Model IDFrom service test mode, press Start/Pause
  • t02 - Fault CodesFrom service test mode, navigate to t02 and press Start/Pause
  • t03 - Software IDFrom service test mode, navigate to t03 and press Start/Pause to alternate between UL (UL code)…
  • t04 - LED Illumination and Button TestFrom service test mode, navigate to t04 and press Start/Pause.
  • t05 - Pump TestFrom service test mode, navigate to t05 and press Start/Pause.
  • t06 - Water Level Sensor TestFrom service test mode, navigate to t06 and press Start/Pause
  • t07 - Thermistor/Heater TestFrom service test mode, navigate to t07 and press Start/Pause.
  • t08 - Steam TestFrom service test mode, navigate to t08 and press Start/Pause.
  • t09 - Spray TestFrom service test mode, navigate to t09 and press Start/Pause.
  • t10 - Tumble TestFrom service test mode, navigate to t10 and press Start/Pause.
  • t11 - Spin TestFrom service test mode, navigate to t11 and press Start/Pause
  • t12 - Dispenser TestFrom service test mode, navigate to t12 and press Start/Pause to advance
  • t13 - EOL TestFrom service test mode, navigate to t13 and press Start/Pause.

Full entry steps, exit procedures, and test sequences are available in Max.

Related GE washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass