mypros+
Error code reference

Kenmore Washer Error Code E75

Better models only

Kenmore codesKenmore washer codes

Better models only - Water temperature sensor circuit fault.

First step from the service manual

Check the resistance of the NTC; should be around 50K ohms (Refer to test 14).

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for E75.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E75 means on a Kenmore washer

The E75 error code on Kenmore washers indicates a fault in the water temperature sensor circuit. This code appears on better-equipped models that include an NTC (Negative Temperature Coefficient) thermistor for monitoring incoming or drum water temperature. The NTC thermistor changes its electrical resistance in response to temperature, and the control board uses this resistance reading to regulate heating and cycle timing. When the board detects a resistance value outside the expected operating range, it triggers E75 to alert the technician to a circuit problem.

The primary diagnostic step for E75 is to measure the resistance of the NTC thermistor. A properly functioning sensor should read approximately 50K ohms. Readings significantly above or below this value indicate a failed sensor, while correct resistance with a continuing fault code may point to wiring or connection issues between the sensor and the control board. This test is referenced as Test 14 in the diagnostic procedure for this platform.

Common causes include a degraded or open-circuit NTC thermistor, damaged wiring harness connections, corrosion at the sensor connector, or a faulty control board that misreads the signal. Because water exposure is constant in a washer environment, connector corrosion and wire chafing are realistic failure points alongside the sensor itself. Resolving E75 typically requires isolating whether the fault lies in the sensor, the wiring path, or the board.

Source: manufacturer service documentation.

Common causes of E75

  1. 01

    Failed NTC thermistor

    Part replacement

    The NTC temperature sensor itself has failed, producing a resistance reading well outside the expected 50K ohm value. This is the most likely cause and is confirmed by measuring the sensor directly with a multimeter.

  2. 02

    Corroded or loose sensor connector

    Wiring / connection

    Moisture in the washer environment can cause corrosion at the connector pins linking the NTC thermistor to the wiring harness. Inspect the connector for green or white oxidation and ensure it is fully seated.

  3. 03

    Damaged wiring harness

    Part replacement

    Wires running between the temperature sensor and the control board can chafe, pinch, or break over time. Visually trace the harness for any wear points, cuts, or heat damage and test for continuity.

  4. 04

    Open circuit in the sensor lead

    Part replacement

    An open circuit in the sensor circuit will cause the control board to read no signal at all, triggering E75. This can result from a broken wire or a completely failed sensor and will show as infinite resistance on a multimeter.

  5. 05

    Faulty control board

    Part replacement

    If the NTC thermistor measures correctly at approximately 50K ohms and the wiring shows no faults, the control board may be misreading or failing to process the sensor signal. This is the least common cause and should be diagnosed only after ruling out the sensor and wiring.

See the test procedure for each cause

Frequently asked questions about E75

What does E75 mean on a Kenmore washer?
E75 indicates a fault in the water temperature sensor circuit. This code is specific to better-equipped Kenmore washer models that use an NTC thermistor to monitor water temperature. The control board has detected a resistance reading outside the normal operating range, which prevents it from accurately tracking water temperature during a cycle.
How do I fix the E75 error code on my Kenmore washer?
Start by testing the NTC thermistor resistance using a multimeter. The sensor should read approximately 50K ohms. If the reading is significantly off, the sensor needs to be replaced. If the sensor reads correctly, inspect the wiring harness and connectors for corrosion, damage, or loose connections between the sensor and the control board.
Will resetting my Kenmore washer clear the E75 code?
A power reset may temporarily clear the E75 code, but it will return if the underlying fault in the temperature sensor circuit has not been repaired. The code is triggered by an actual circuit condition, not a random software glitch, so a reset alone is not a fix. The sensor and wiring must be tested and any faulty components replaced.
Is it safe to use my Kenmore washer while it shows E75?
It is not recommended to continue running the washer while E75 is active. Without accurate temperature sensing, the control board cannot properly regulate water temperature, which could lead to inadequate cleaning, fabric damage, or other cycle errors. Addressing the fault before continued use is the safer approach.
How much does it cost to repair a Kenmore washer E75 error?
Repair costs depend on which component is at fault. Replacing the NTC thermistor is generally the least expensive fix, with parts typically ranging from $15 to $50 and professional labor adding $80 to $150 or more depending on your area. If the control board is the cause, parts alone can range from $100 to $300 or higher, making professional diagnosis important before committing to a repair.

Related Kenmore washer codes

All Kenmore washer codes
View all 156 Kenmore washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass