Error code reference

GE Oven Error Code F93

Lower oven door becomes locked while expected to be unlocked (during standby or cooking).

GE codesGE oven codes

Lower oven door becomes locked while expected to be unlocked (during standby or cooking).

First step from the service manual

Check the door lock and harness between the door lock and the control; replace the door lock and/or replace the control.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F93.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F93 means on a GE oven

The F93 error code indicates the Electronic Range Control (ERC) has detected a fault in the lower oven door latch switch circuit. The control board monitors both the lock and unlock positions of the door latch mechanism through dedicated switch circuits. When the signals from these circuits fall outside expected parameters, or when continuity checks on the latch switch wiring fail, the board sets F93. Diagnosis begins at the T012 ERC by checking continuity from the Yellow/White pin 10 to Blue pin 4 for the unlocked position, and Yellow/White pin 6 to Orange pin 5 for the locked position. On units with Machine Control, the check moves to connector J900, pins 1 and 2, tracing the Yellow/White to Orange/White wires on the lower board.

For homeowners, this code means the oven's control system cannot confirm whether the lower oven door is properly locked or unlocked. GE ranges with self-clean functions use a motorized latch to secure the door during high-temperature cycles. If the switch that reports the latch position stops working correctly, the oven triggers F93 to prevent unsafe operation.

This fault is most often caused by a wiring issue, a failed latch switch, or a damaged latch motor assembly rather than the control board itself. The circuit involves specific connectors and wire colors that can be verified with a multimeter before replacing any parts.

Source: manufacturer service documentation.

Common causes of F93

  1. 01

    Open or shorted latch switch wiring

    Wiring / connection

    The wires connecting the door latch switch to the ERC or Machine Control can break, burn, or short due to heat exposure near the oven cavity. This interrupts the continuity the control board expects to see on the lock and unlock circuits.

  2. 02

    Failed lower oven door latch switch

    Part replacement

    The latch switch itself can fail mechanically or electrically, preventing it from reporting the correct locked or unlocked position to the control board. A multimeter check across the switch contacts will confirm whether it opens and closes as designed.

  3. 03

    Faulty door latch motor assembly

    Part replacement

    If the latch motor fails to fully drive the latch into the locked or unlocked position, the switch never actuates correctly, and the circuit reads as faulted. This is common after repeated self-clean cycles where the motor experiences sustained high heat.

  4. 04

    Failed ERC or Machine Control board

    Part replacement

    If all wiring and switch components test correctly but F93 persists, the ERC or the lower board connector J900 may have internal damage affecting how the latch circuit signals are read. This is the least common cause and should only be considered after all other components are verified.

See the test procedure for each cause

Frequently asked questions about F93

What does F93 mean on a GE oven?
F93 means the control board has detected a fault in the lower oven door latch switch circuit. The oven cannot confirm whether the door latch is in the locked or unlocked position. This typically points to a wiring issue, a bad latch switch, or a failed latch motor assembly on the lower oven door.
How do I fix F93 on a GE oven?
Start by closing the lower oven door and testing continuity in the latch switch circuits using a multimeter. On a T012 ERC, check from Yellow/White pin 10 to Blue pin 4 for the unlocked circuit, and Yellow/White pin 6 to Orange pin 5 for the locked circuit. On Machine Control units, check connector J900 pins 1 and 2 for Yellow/White to Orange/White continuity on the lower board. If continuity fails, inspect the wiring harness for damage first, then test the latch switch and latch motor assembly before considering board replacement.
Can I still use my GE oven with an F93 error code?
Normal baking and broiling may still function depending on how the fault presents, but you should not run a self-clean cycle with F93 active. The self-clean cycle requires the door latch to lock securely, and with the latch circuit faulted, the oven cannot verify that the door is locked at the extreme temperatures self-clean generates. Resolve the F93 fault before using the self-clean function.
How much does it cost to fix an F93 error on a GE oven?
If the fix is a damaged wiring harness or connector, repair cost may be limited to labor or a low-cost harness repair. A replacement door latch switch or latch motor assembly typically runs between $30 and $80 in parts. If the ERC or Machine Control board needs replacement, parts alone can range from $100 to $300 or more depending on the model. A repair technician's diagnostic visit generally adds $75 to $150 in labor, which is worthwhile before purchasing a control board.
Is F93 on a GE oven a hard fix or does it require a technician?
A DIYer comfortable with a multimeter can perform the continuity checks on the latch switch circuits and inspect the wiring harness without professional help. Replacing the latch switch or latch motor assembly is also manageable with basic appliance repair skills and the correct part. If the fault traces back to the ERC or Machine Control board, professional diagnosis is advisable to avoid purchasing an expensive part unnecessarily.

Related GE oven codes

All GE oven codes
View all 134 GE oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass