mypros+
Error code reference

GE Refrigerator Error Code F-1-f

Ice Room Sensor Error

GE codesGE refrigerator codes

Ice Room Sensor Error — sensor housing separation, contact error, disconnection, or short circuit.

First step from the service manual

Check voltage at MAIN PCB CN32 pin 3 to CN75 pin 1; should be between 4.5V to 1.0V.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F-1-f.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F-1-f means on a GE refrigerator

The F-1-f error code on a GE refrigerator indicates an Ice Room Sensor fault. This sensor monitors temperature within the ice-making compartment, and the control system uses its readings to regulate ice production cycles. When the main PCB detects an abnormal signal from this sensor, it logs the F-1-f code and may suspend ice maker operation to prevent damage or unsafe conditions. The sensor itself is a thermistor-type component whose resistance changes with temperature, and the board interprets that resistance as a corresponding voltage signal.

The diagnostic process begins at the main PCB by checking the voltage between connector CN32 pin 3 and connector CN75 pin 1. Under normal operating conditions, this voltage should fall within the range of 1.0V to 4.5V. A reading outside this window points to a fault in the sensor circuit. Possible causes include physical separation of the sensor from its housing, a wiring connection that has loosened or corroded at the connector pins, a complete wire break causing an open circuit, or a short circuit in the sensor wiring harness.

Because the fault covers several failure modes, systematic inspection of the entire sensor circuit is necessary. Technicians should visually confirm the sensor is properly seated in its housing, inspect the wiring harness from the sensor back to the main PCB for any pinched, chafed, or broken wires, and check the connector pins at CN32 and CN75 for corrosion or back-out. If wiring and connections test acceptable, the thermistor sensor itself should be tested for proper resistance and replaced if out of specification.

Source: manufacturer service documentation.

Common causes of F-1-f

  1. 01

    Loose or disconnected wiring connector

    Wiring / connection

    The connector at CN32 or CN75 on the main PCB may have worked loose over time due to vibration or handling. Check both connectors for secure seating and inspect the pins for any signs of corrosion or bent contacts.

  2. 02

    Sensor separation from housing

    Wiring / connection

    The ice room sensor can physically separate from its mounting housing, breaking reliable thermal contact and causing erratic or out-of-range voltage readings. Visually inspect the sensor to confirm it is fully seated and secured in its bracket.

  3. 03

    Short circuit in sensor wiring harness

    Part replacement

    A short circuit in the wiring between the sensor and the PCB will pull the voltage signal outside the normal 1.0V to 4.5V range. Inspect the harness for pinched, chafed, or melted wire insulation, particularly where it routes through cabinet panels.

  4. 04

    Open circuit or broken wire

    Part replacement

    A broken wire anywhere along the sensor circuit creates an open circuit, causing the voltage at CN32 pin 3 to CN75 pin 1 to read at an extreme value outside the acceptable range. Continuity testing of the full harness will identify the break.

  5. 05

    Failed ice room thermistor sensor

    Part replacement

    If all wiring and connectors check out, the thermistor sensor itself may have failed internally, producing a resistance value that is out of specification. Replacing the sensor is required if the voltage reading remains abnormal after confirming the wiring is intact.

See the test procedure for each cause

Frequently asked questions about F-1-f

What does F-1-f mean on a GE refrigerator?
The F-1-f code indicates an Ice Room Sensor error. The main PCB has detected a problem with the temperature sensor in the ice-making compartment, which could be caused by sensor housing separation, a loose or corroded connector, a broken wire, or a short circuit in the sensor circuit. The first diagnostic step is to measure the voltage at main PCB connector CN32 pin 3 to CN75 pin 1, which should read between 1.0V and 4.5V under normal conditions.
Can I fix the F-1-f error code myself?
Some causes of the F-1-f code are DIY-accessible, such as reseating a loose connector at the main PCB or repositioning a sensor that has slipped out of its housing. However, diagnosing a short circuit or open circuit in the wiring harness requires a multimeter and basic electrical knowledge. If the fault points to the main PCB itself, professional repair is recommended.
Will resetting the refrigerator clear the F-1-f error?
A power reset may temporarily clear the F-1-f code, but if the underlying fault in the ice room sensor circuit is still present, the code will return. The error needs to be resolved at the source by inspecting and repairing the sensor, wiring, or connectors before the code will stay cleared.
Is it safe to keep using my refrigerator when the F-1-f code is active?
The F-1-f fault affects the ice room sensor circuit, so the refrigerator's main cooling and food preservation functions are typically not compromised. However, ice maker operation may be unreliable or disabled while the code is active. It is advisable to address the fault promptly to restore normal ice production and prevent any further electrical issues in the sensor circuit.
How much does it cost to repair the F-1-f error on a GE refrigerator?
Repair costs depend on the specific cause. If only a wiring connector needs reseating, there may be no parts cost and minimal labor. Replacing the ice room thermistor sensor typically costs in the range of $20 to $60 for the part. If a wiring harness or the main PCB is involved, total repair costs including labor can range from $150 to $400 or more, depending on local service rates and parts availability.

Related GE refrigerator codes

All GE refrigerator codes
View all 540 GE refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass