mypros+
Error code reference

GE Refrigerator Error Code F507

Cold Water paddle switch input present

GE codesGE refrigerator codes

Cold Water paddle switch input present - check paddle switch and wiring.

First step from the service manual

Check paddle switch and wiring.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F507.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F507 means on a GE refrigerator

The F507 error code on a GE refrigerator indicates that the control board is detecting a continuous input signal from the cold water paddle switch when it should not be active. The cold water paddle switch is a momentary contact switch located behind the dispenser paddle on the door. When a user presses the paddle to dispense water, the switch closes and sends a signal to the control board. Under normal operation, that signal exists only while the paddle is physically pressed. When F507 appears, the board is reading the switch as permanently closed or stuck in the active position.

The most common cause is a mechanically stuck or faulty paddle switch that is physically jammed in the depressed position or has failed internally with its contacts welded shut. Wiring issues are the next consideration, including a pinched wire in the door harness that short-circuits the signal line, a corroded connector at the switch or control board, or a damaged wire caused by repeated door opening and flexing over time. The door wiring harness on refrigerators with in-door dispensers passes through a hinge area that is subject to repeated bending stress, making wire fatigue a realistic failure point.

To diagnose F507, begin by visually inspecting the paddle and the dispenser recess for any debris, ice, or mechanical obstruction holding the paddle inward. With the refrigerator unplugged, disconnect the paddle switch and check continuity across its terminals. A properly functioning momentary switch should show no continuity when at rest. If continuity is present at rest, the switch has failed and needs replacement. If the switch tests correctly, inspect the wiring harness from the switch back to the dispenser control board for shorts or damaged insulation.

Source: manufacturer service documentation.

Common causes of F507

  1. 01

    Stuck or failed paddle switch

    Part replacement

    The momentary contact switch behind the dispenser paddle can fail with its internal contacts permanently closed, or the paddle mechanism can become physically jammed by ice or debris. Disconnect the switch and test for continuity at rest; continuous continuity confirms switch failure.

  2. 02

    Short circuit in door wiring harness

    Part replacement

    The wiring harness running through the refrigerator door hinge area flexes with every door opening and can develop internal wire breaks or insulation damage that cause two conductors to contact each other. Inspect the harness closely at the hinge flex point for visible damage.

  3. 03

    Corroded or loose connector

    Wiring / connection

    The connector at the paddle switch or at the dispenser control board can corrode or work loose over time, creating an unintended circuit path that mimics a closed switch. Unplug the refrigerator, disconnect the connectors, and inspect the terminals for green corrosion or bent pins.

  4. 04

    Ice or debris obstructing the paddle

    Wiring / connection

    Ice buildup or food debris lodged in the dispenser recess can physically hold the paddle in a partially depressed position, keeping the switch closed. Inspect the dispenser area visually and clear any obstructions before proceeding to electrical diagnosis.

  5. 05

    Faulty dispenser control board

    Part replacement

    If the paddle switch and all wiring check out correctly, the dispenser control board itself may be misreading the switch input due to a failed input circuit. This is the least likely cause and should only be considered after the switch and harness are confirmed good.

See the test procedure for each cause

Frequently asked questions about F507

What does F507 mean on a GE refrigerator?
F507 means the refrigerator control board is detecting a constant input signal from the cold water dispenser paddle switch. Normally, this signal is only present when someone physically presses the paddle to get water. The code indicates the switch is stuck closed, the wiring has a short circuit, or there is a connector problem keeping the circuit continuously active.
Can I fix F507 myself or do I need a technician?
Some causes of F507 are DIY-friendly. Clearing debris or ice from the dispenser recess and inspecting wiring connectors for corrosion are straightforward tasks. Testing the paddle switch with a multimeter and replacing it is also within reach for someone comfortable with basic appliance repair. However, if the door wiring harness needs replacement or the control board is faulty, a technician familiar with GE dispensers is recommended.
Is it safe to keep using my refrigerator while F507 is active?
The refrigerator's cooling and food preservation functions are generally not affected by F507, so the appliance is not unsafe to use for storing food. However, the water dispenser may behave erratically or stop working while the fault is active. Leaving a wiring short unaddressed for an extended period is not advisable, so prompt diagnosis is recommended.
Will resetting the refrigerator clear the F507 error code?
A power reset by unplugging the refrigerator for a few minutes may temporarily clear the code, but F507 will return if the underlying problem with the paddle switch or wiring is not corrected. A reset alone does not fix a stuck switch, a shorted wire, or a corroded connector. Resolving the fault requires identifying and correcting the root cause.
How much does it cost to repair a GE refrigerator F507 error?
Repair costs depend on which component has failed. A replacement paddle switch is typically a low-cost part, often in the range of $15 to $50, and is a manageable DIY repair. If the door wiring harness needs replacement, parts and labor combined can range from $100 to $250 or more depending on the model and technician rates. A dispenser control board replacement tends to be at the higher end of the cost spectrum, potentially $150 to $350 including parts and labor.

Related GE refrigerator codes

All GE refrigerator codes
View all 540 GE refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass