mypros+
Error code reference

LG Refrigerator Error Code LED 6 blinks

Compressor activation overcurrent error

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the LED 6 blinks error code actually means

Your LG refrigerator has detected that its compressor is drawing too much electrical current, which can happen when the fridge is working too hard or has a failing part. This is a protective fault that shuts things down to prevent further damage. The issue could be something as simple as the room being too hot, or it may point to a failing fan or compressor that needs professional attention.

Diagnostic procedure

The full LED 6 blinks procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check normal performance after power reset; if same error recurs, replace main board; if occurs twice, replace compressor.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock LED 6 blinks procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of LED 6 blinks

Ranked by how often they cause this code
  1. 1Condenser fan failure
  2. 2Abnormal ambient temperature above 43 degrees Celsius
  3. 3Faulty main PCB
  4. 4Compressor failure

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about LED 6 blinks

What does LED 6 blinks mean on a LG refrigerator?
LED 6 blinks on an LG refrigerator signals a compressor activation overcurrent error. The main PCB has detected that the compressor is drawing more current than expected, which indicates an overloading condition. Possible causes include ambient temperatures above 43 degrees Celsius, a failed condenser fan, a failing compressor, or a faulty control board.
How do I fix the LED 6 blinks error on my LG refrigerator?
Start by unplugging the refrigerator for several minutes and then restoring power to perform a reset. If the error returns, the next step is replacing the main PCB. If the fault appears again after PCB replacement, the compressor itself needs to be replaced. Also check that the condenser fan is working and that the installation area is not excessively hot.
How much does it cost to repair the LED 6 blinks error on an LG refrigerator?
Repair costs vary depending on which component is at fault. Replacing a condenser fan motor is generally the least expensive repair, typically ranging from $75 to $200 including parts and labor. A main PCB replacement can range from $150 to $400. Compressor replacement is the most expensive option, often ranging from $400 to $800 or more depending on the model and labor rates in your area.
Will resetting my LG refrigerator clear the LED 6 blinks error?
A power reset is the recommended first diagnostic step and may clear the error if the fault was transient. However, if the same error returns after the reset, the underlying cause must be addressed. Persistent recurrence after reset points toward a faulty main PCB or compressor that will need to be replaced.
Is it safe to keep using my LG refrigerator when it shows the LED 6 blinks error?
Continuing to operate the refrigerator with an active overcurrent fault is not recommended, as the condition that triggered the error can cause further damage to the compressor or electrical components. The fault code is a protective measure, and the underlying cause should be diagnosed and corrected before relying on the unit to maintain safe food temperatures.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass